LD6M-3M - User Manual LD6M-3M - User Manual

LD6M-3M - User Manual

LD6M-3M - User Manual LD6M-3M - User Manual

User Manual          Rev 1.10

 

Please scan below QRCode to download EZCast App for upgrading your MiraScreen plug & play products.

 

Video Guide

https://youtube.com/c/MiraScreen

Subscribe to our handy videos to learn more about mirroring with MiraScreen.

 

Hardware Installation

LD6M-3M

Please follow below steps to setup MiraScreen Wire+:

Step 1, plug dongle in to HD port of your TV, Monitor, or Projector. 

Step 2, plug one end of the cable (USB Type-A) into an external 5V/1A power adapter.

Step 3. Plug the lightning/Micro USB/Type-C port to your smartphone (iOS/Android). 

Note: supports iOS 9+

Step 4, please select to the right TV HD source, MiraScreen Wire+ setup page will show on your TV, please refer to below picture.

 LD6M-3M

 

For iOS (iPhone/iPad) devices Airplay Mirroring

If the connection is right, iOS device popups a ‘Trust This Computer’ message please select ‘Trust’. Please wait for a few seconds, your iOS device screen will mirror to the TV screen.

Note: Some iOS devices may popup "This accessory may not be supported".  Please feel at ease to use, as this is a normal notification. Or you can change the power adapter for more stable power supply and make sure the adapter support 5V/1A output.

 LD6M-3MLD6M-3M

 

Firmware upgrade and EZCast

App software installation:

If you encounter a system barrier(it may happens after iOS software version upgrade) leading to device cannot be used normally, please try the steps below to upgrade your dongle:
Step 1.Insert a paper clip into the hole on the MiraScreen Wire+, and push the key inside the hole to switch to “Airplay & Setup mode” (OTA mode).

LD6M-3M

LD6M-3M

Step 2.please turn on the Personal Hotspot for connection

LD6M-3M

Step 3.Please connect your phone to MiraScreen Wire, you will see a message. If it connects successfully, you will see the picture “” shown on your TV. If it shows an icon “”, it means the connection failed. Please re-check from step 1 to step 3.

LD6M-3M

Step 4.Download EZCast app from Apple App store. Then please launch the “EZCast” app and click the “Wire” button to establish connection between your iOS device and MiraScreen Wire+.After that please click the “Menu” button.

Step 5, click the “Upgrade” button on the menu page and wait for  the update.

LD6M-3M

LD6M-3M

Note: Please DO NOT power off or unplug your Mirascreen Wire+ dongle power cable during upgrade and make sure your cellular data (3G/4G) is available.

Step 6.After firmware upgrade, please insert a paper clip into the hole, and push the butto inside the hole to switch to Plug&Play mode for enjoying big screen casting.

 

For Android functional operation (only for MiraScreen Wire+)

Connect Android phones or pad to MiraScreen Wire+

Please follow the hardware installation steps (1 to 4). NOTE: Please do not use iOS lightning cable instead of Android USB cable. Android USB cable is needed.

1.Software Installation (Only Android)

Please download “EZCast” from Google play  store(Android).

You may also scan the QR code on TV screen for download.

Note: Supports Android 4.4 and above

*Note: Not all Android 4.4 devices support USB Mirror.

2.Android Mirror function:

(A) Android mirroring mode

Please launch the “EZCast” app, and click the “” button. After that please click the “Connect” button, and then enable “USB tethering”. Then you may start mirroring your Android screen.

Note: Supports Android 5.0 and above and the audio stay on you phone. After mirroring, please do not turn off EZCat app. 

LD6M-3M

Note: If the MiraScreen Wire+ is abnormal due to mobile phones or tab software upgrade, please use EZCast app/Upgrade to do firmware upgrade via OTA. Please refer to page 6 to page 7 (Firmware Upgrade).

(B) Android USB Mirror mode

USB Mirror mode is an alternative for supporting more Android devices (4.4 and above). Please launch the “EZCast” app, and then enable “USB tethering” according to previous section.

Click the “Menu” button, and then “USB Mirror” button on menu page, and follow the App instructions to enable “USB debugging”. You may start mirroring your Android screen. If “USB Mirror” failed to enable, please unplug USB cable from your Android device, and then re-plug in for retry.

LD6M-3M

LD6M-3M

 

Note: Supports Android 4.4 and above

Note: USB debugging should be turned on for activating USB Mirror.

Note: Not all Android 4.4 devices support USB Mirror.

**Not all smartphone supports USB audio, and consequently the sound may come from the smartphone instead of TV/Projector.

3.Android Audio control

Some Android phones may not transfer the audio to the TV via USB cable. In order to not affect the video image, please follow the steps below to change the audio output and keep the audio staying on the phone:

Launch EZCast app; click the “Wire” icon on the function page in the upper right corner to establish the connection between your phone and the dongle. Then click the menu icon on the upper left corner of the function page, click “Setting” and you will see the setting page below.

LD6M-3M

Note: Due to the EZCast app will update time to time to compatible with up-to-date devices. More information about EZCast app, please refer to https://mirascreen.com/pages/download-ezcast

Find details by your smart phone brand / model: https://www.MiraScreen.com/help

 

  Repair Tool

In rare events where you might have trouble OTA the dongle firmware to the latest version, you may consider using the Repair Tool to upgrade your MiraScreen.

Check out LD6M-3M repair tool >>

 

Customer Service

Support@MiraScreen.com

We’d love to hear from you!